Latest post Mon, Jul 29 2019 2:42 PM by Dom Q. Silverio. 1 replies.
Page 1 of 1 (2 items)
Sort Posts: Previous Next
  • Mon, Jul 29 2019 7:46 AM

    S4810 configuration

    Hi All,

    I have an S4810, that was setup in Avid config.

    As I understand, the Avid config allows 6 x 10 GigE devices, and 42 x 1 GigE devices.

    I need to add on additional 10gigE devices, but when I do this, on some of my devices I am only getting only 1 GigE speeds, even though there is a link speed reported of 10000 Mbit.

    Here is the output of show interfaces for the port:

    Avid-Core#show interfaces te 0/33

    TenGigabitEthernet 0/33 is up, line protocol is up
    Hardware is DellForce10Eth, address is 00:01:e8:8b:8f:f5
    Current address is 00:01:e8:8b:8f:f5
    Pluggable media present, SFP+ type is 10GBASE-SR
    Medium is MultiRate, Wavelength is 850nm
    SFP+ receive power reading is -3.3630dBm
    Interface index is 42271746
    Internet address is not set
    Mode of IPv4 Address Assignment : NONE
    DHCP Client-ID :0001e88b8ff5
    MTU 1554 bytes, IP MTU 1500 bytes
    LineSpeed 10000 Mbit
    Flowcontrol rx on tx off
    ARP type: ARPA, ARP Timeout 04:00:00
    Last clearing of "show interface" counters 4d14h12m
    Queueing strategy: fifo
    Input Statistics:
    4637093140 packets, 6713424339313 bytes
    220154 64-byte pkts, 165896428 over 64-byte pkts, 31896969 over 127-byte pkts
    7761398 over 255-byte pkts, 30433641 over 511-byte pkts, 4400884550 over 1023-byte pkts
    15294 Multicasts, 14607 Broadcasts
    0 runts, 0 giants, 7 throttles
    0 CRC, 0 overrun, 0 discarded
    Output Statistics:
    988706780 packets, 1139104360505 bytes, 0 underruns
    3681406 64-byte pkts, 134682423 over 64-byte pkts, 106801396 over 127-byte pkts
    4094702 over 255-byte pkts, 14846354 over 511-byte pkts, 724600499 over 1023-byte pkts
    510075 Multicasts, 3919874 Broadcasts, 984276831 Unicasts
    0 throttles, 0 discarded, 0 collisions, 0 wreddrops
    Rate info (interval 299 seconds):
    Input 00.00 Mbits/sec, 1 packets/sec, 0.00% of line-rate
    Output 00.00 Mbits/sec, 17 packets/sec, 0.00% of line-rate
    Time since last interface status change: 3d5h33m

    Currently, I am seeing a maximum of 100 MB/s throughput on this port, even though both the switch and device are reporting 10000 Mbit connections.

    Show config on the port shows this:

    interface TenGigabitEthernet 0/33

     no ip address

     switchport

     flowcontrol rx on tx off  

     spanning-tree 0 portfast 

     no shutdown

     

    So I'm at a loss why I'm not getting any additional speed out of the system. 

  • Mon, Jul 29 2019 2:42 PM In reply to

    Re: S4810 configuration

    The S4810 can accommodate 48 10GbE connections. There is enough bandwidth in the fiber to do so. One of our switches is currently hosting around 40 connections at that speed.

     

    What device are you using? Do you have a device bandwidth limit on in the Nexis/ISIS GUI? Tested with Path Diag, both directions indicate ~100 MB/s?

     

     

    MC 8.6.1, Windows 10, ASROCK X99M, Intel 5930K, Zotac GTX970, 32GB RAM, Transcend 512GB M.2 SSD & Dell U2713H. MBP 2012 Thunderbolt, OSX 10.10.5, MC... [view my complete system specs]
Page 1 of 1 (2 items)

© Copyright 2011 Avid Technology, Inc.  Terms of Use |  Privacy Policy |  Site Map |  Find a Reseller